Chroma 62015B-30-50

Chroma 62015B-30-50 The Chroma 62015B-30-50 DC Power Supply Module, with its many unique features, is designed for burn-in applications such as the LCD panels, DC-DC converters, power inverters, notebook computers, battery chargers and many other typs of electronic devices.  Its high power density and low cur ripple make it very cost effective. Designed with Modern power factor correction circuitry it meets IEC requirements.
 Features and Specifications of the Chroma 62015B-30-50 DC Power Supply Module include:

Features:

• N+1 Redundancy
• Hot-Swappable Maintenance
• Ideal for Burn-in and Plating
• High Power Applications with CSU
• Remote Sense
• Remote ON / OFF
• CAN Bus Control
• DC OK Signal Output
• Voltage range: 1 ~ 30V
• Cur range: Up to 2000A (System)
• Power range up to 1.5KW per module up to 120KW per system
• High Power Density (464 mW / cm3 = 7.13 W/In3)

Specifications:

• Electrical Specifications:
  • Output Ratings:
    • Output Power:  1500W
    • Output Voltage:  1~30V
    • Output Cur:  1~50A
  • LIne Regulation:  0.1% FS
  • Load Regulation:  1% FS
  • Programming Accuracy:  1% FS
  • Measurement Accuracy:  1% FS
  • Output Noise (20MHz):
    • Voltage Noised (P-P):  100mV
    • Voltage Ripple (rms):  30mV
    • Cur Ripple (rms):  0.5A
  • Efficiency:  > 88% @ full load
  • Turn On Over Shoot Voltage (Rise Time of 100ms):  5% of nominal output
  • Transient Response Time:  < 5 ms
  • AC Input Voltage:
    • Six Position Mainframe:  187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
    • Three Position Mainframe:  187 to 250 Vac (single phase) / 45 ~ 65 Hz
    • Input Power Factor:  > 0.98@ full load
• Protection Function:
  • OVP:  Automatically shuts down at 115% of set value
  • Adjustment Range:  1~31V
  • OCP:  Cur limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
  • OTP:  Automatically shuts down if internal limit is reached
• I/O Signal:
  • Remote ON/OFF (I/P):  Dry contact (closed = enabled), vice versa
  • AUX Voltage:  4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)
  • DC OK Signal Type (O/P):  Dry contact (closed = enabled) (Error : OVP / OCP / OTP / AC Fault)
• Programming Response Time (Six Position Mainframe through CAN) (Typical):
  • Rise Time (Full Load):  For a programmed 5% to 95% step in output voltage : 100ms
  • Rise Time (No Load):  For a programmed 5% to 95% step in output voltage : 100ms
  • Fall Time (Full Load):  For a programmed 95% to 5% step in output voltage : 40ms
  • Fall Time (No Load):  For a programmed 95% to 5% step in output voltage : 5s
  • Vout Setting:  CAN Bus send command to DC module receiver : 1s
  • Measurement V & I:  Under CAN command using fetch : 100ms
  • Delay Time:  For output ON/OFF enable and disable (under CAN command) : 5s(Single Mainframe)
• General Specifications:
  • Remote Sensing:  3V maximum line loss compensation
  • Parallel Operation:  Cur Sharing (±5%)
  • Operating Temperature:  0 ~ 50°C
  • Humidity Range:  0 ~ 90% RH. Non-condensing
  • Remote Interface:  CAN Bus (optional)
  • Safety & EMC:  CE
     

N+1 Redundancy

Hot-Swappable Maintenance

Ideal for Burn-in and Plating

High Power Applications with CSU

Remote Sense

Remote ON / OFF

CAN Bus Control

DC OK Signal Output

Voltage range: 1 ~ 30V

Cur range: Up to 2000A (System)

Power range up to 1.5KW per module up to 120KW per system

High Power Density (464 mW / cm3 = 7.13 W/In3)

Electrical Specifications:

• Output Ratings:
  • Output Power:  1500W
  • Output Voltage:  1~30V
  • Output Cur:  1~50A
• LIne Regulation:  0.1% FS
• Load Regulation:  1% FS
• Programming Accuracy:  1% FS
• Measurement Accuracy:  1% FS
• Output Noise (20MHz):
  • Voltage Noised (P-P):  100mV
  • Voltage Ripple (rms):  30mV
  • Cur Ripple (rms):  0.5A
• Efficiency:  > 88% @ full load
• Turn On Over Shoot Voltage (Rise Time of 100ms):  5% of nominal output
• Transient Response Time:  < 5 ms
• AC Input Voltage:
  • Six Position Mainframe:  187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
  • Three Position Mainframe:  187 to 250 Vac (single phase) / 45 ~ 65 Hz
  • Input Power Factor:  > 0.98@ full load

Protection Function:

• OVP:  Automatically shuts down at 115% of set value
• Adjustment Range:  1~31V
• OCP:  Cur limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
• OTP:  Automatically shuts down if internal limit is reached

I/O Signal:

• Remote ON/OFF (I/P):  Dry contact (closed = enabled), vice versa
• AUX Voltage:  4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)
• DC OK Signal Type (O/P):  Dry contact (closed = enabled) (Error : OVP / OCP / OTP / AC Fault)

Programming Response Time (Six Position Mainframe through CAN) (Typical):

• Rise Time (Full Load):  For a programmed 5% to 95% step in output voltage : 100ms
• Rise Time (No Load):  For a programmed 5% to 95% step in output voltage : 100ms
• Fall Time (Full Load):  For a programmed 95% to 5% step in output voltage : 40ms
• Fall Time (No Load):  For a programmed 95% to 5% step in output voltage : 5s
• Vout Setting:  CAN Bus send command to DC module receiver : 1s
• Measurement V & I:  Under CAN command using fetch : 100ms
• Delay Time:  For output ON/OFF enable and disable (under CAN command) : 5s(Single Mainframe)

General Specifications:

• Remote Sensing:  3V maximum line loss compensation
• Parallel Operation:  Cur Sharing (±5%)
• Operating Temperature:  0 ~ 50°C
• Humidity Range:  0 ~ 90% RH. Non-condensing
• Remote Interface:  CAN Bus (optional)
• Safety & EMC:  CE
   

Output Ratings:

• Output Power:  1500W
• Output Voltage:  1~30V
• Output Cur:  1~50A

LIne Regulation:  0.1% FS

Load Regulation:  1% FS

Programming Accuracy:  1% FS

Measurement Accuracy:  1% FS

Output Noise (20MHz):

• Voltage Noised (P-P):  100mV
• Voltage Ripple (rms):  30mV
• Cur Ripple (rms):  0.5A

Efficiency:  > 88% @ full load

Turn On Over Shoot Voltage (Rise Time of 100ms):  5% of nominal output

Transient Response Time:  < 5 ms

AC Input Voltage:

• Six Position Mainframe:  187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz
• Three Position Mainframe:  187 to 250 Vac (single phase) / 45 ~ 65 Hz
• Input Power Factor:  > 0.98@ full load

Output Power:  1500W

Output Voltage:  1~30V

Output Cur:  1~50A

Voltage Noised (P-P):  100mV

Voltage Ripple (rms):  30mV

Cur Ripple (rms):  0.5A

Six Position Mainframe:  187 ~ 250 Vac (3 Phase 4 Wire, Δ Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) / 45 ~ 65 Hz

Three Position Mainframe:  187 to 250 Vac (single phase) / 45 ~ 65 Hz

Input Power Factor:  > 0.98@ full load

OVP:  Automatically shuts down at 115% of set value

Adjustment Range:  1~31V

OCP:  Cur limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.

OTP:  Automatically shuts down if internal limit is reached

Remote ON/OFF (I/P):  Dry contact (closed = enabled), vice versa

AUX Voltage:  4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)

DC OK Signal Type (O/P):  Dry contact (closed = enabled) (Error : OVP / OCP / OTP / AC Fault)

Rise Time (Full Load):  For a programmed 5% to 95% step in output voltage : 100ms

Rise Time (No Load):  For a programmed 5% to 95% step in output voltage : 100ms

Fall Time (Full Load):  For a programmed 95% to 5% step in output voltage : 40ms

Fall Time (No Load):  For a programmed 95% to 5% step in output voltage : 5s

Vout Setting:  CAN Bus send command to DC module receiver : 1s

Measurement V & I:  Under CAN command using fetch : 100ms

Delay Time:  For output ON/OFF enable and disable (under CAN command) : 5s(Single Mainframe)

Remote Sensing:  3V maximum line loss compensation

Parallel Operation:  Cur Sharing (±5%)

Operating Temperature:  0 ~ 50°C

Humidity Range:  0 ~ 90% RH. Non-condensing

Remote Interface:  CAN Bus (optional)

Safety & EMC:  CE